Skip to content
Send an enquiry

Hot water cylinder repairs in Hackney

AC Gas & Boiler Specialists helps with hot water cylinder repairs and replacements, and their controls, for homes and rental properties covering Hackney, Islington and Shoreditch.

No hot water, lukewarm taps or a cylinder that will not heat on time: we trace the fault step by step and put it right.

  • Boilers, gas fires and heating
  • Servicing, repairs and checks
  • One simple enquiry form
  • Hackney, Islington and Shoreditch

About hot water cylinders

If your home has a regular or system boiler rather than a combi, your hot water is stored in a cylinder, usually tucked into an airing cupboard. The boiler heats that water through a copper coil inside the cylinder. A cylinder thermostat tells the system when the water is hot enough, and a motorised valve opens and closes to send boiler water to the coil or to the radiators. Many cylinders also have an electric immersion heater fitted as a backup.

There are two main kinds. A vented cylinder is fed by a cold water tank in the loft and works at low pressure, which is why showers in older houses can feel gentle. An unvented cylinder takes water straight from the mains, gives a much stronger flow and carries extra safety devices, including a pressure relief valve, a temperature relief valve and an expansion vessel. The two behave differently when something goes wrong, so it helps to know which one you have.

This service is for homeowners, tenants and landlords who have lost hot water, are running short of it, or are living with a cylinder that is noisy, leaking or slow to recover after a bath. It also suits anyone thinking about replacing an old copper cylinder and wanting straight advice on whether that is really needed, and landlords who need a tenant's hot water back without paying for parts that were never at fault. Whatever the problem turns out to be, we explain what we found and what it means before anything is changed.

On a visit, we start with the controls, because that is where most faults sit. We check that the programmer is calling for hot water, that the cylinder thermostat is reading correctly and switching, and that the motorised valve is actually opening. We then look at the boiler side of the circuit, including the pump and the pipework to the coil, and at the cylinder itself for leaks, corrosion, scale and poor insulation.

Working in that order matters. A cylinder that will not heat can look like a failed boiler, and a stuck valve can look like a broken cylinder. Testing each part in turn means we replace only what has failed, and you get a clear explanation of what we found before any work is done.

Signs your cylinder needs attention

The most common problem is heating that works but hot water that does not. That pattern nearly always points to the hot water side of the controls: a motorised valve that has seized or lost its motor, a cylinder thermostat that has failed, or a programmer that is no longer sending the signal. The opposite pattern, hot water but no heating, often comes back to the same valve stuck in the other position.

Other signs are slower to show. Water that runs out sooner than it used to can mean a coil furred up with scale, a thermostat set too low, or an immersion heater that has quietly stopped working. Water that comes out scalding hot can mean a thermostat that is not switching off, which is worth having checked soon. Rumbling from the airing cupboard often means scale or overheating.

Leaks need prompt attention. A damp patch under the cylinder, green staining on copper joints or water dripping from the lagging all suggest a failing joint or a cylinder that is starting to corrode. On an unvented cylinder, water running from the discharge pipe, which usually ends outside or over a drain, means one of the safety valves is releasing. That is the system protecting itself, and it is a sign something is not right.

If you notice any of these, turn the immersion heater off if water is leaking near it, note what the system is doing, and get in touch. If you ever smell gas near the boiler, leave the cylinder alone and call the National Gas Emergency Service on 0800 111 999.

What is included

A cylinder visit includes:

  • We find out why there is no hot water, too little of it, or water that runs too hot.
  • We test the cylinder thermostat to see that it reads the temperature correctly and switches the system off.
  • We check that the motorised valve opens and closes fully when hot water is called for.
  • We check the programmer or timer to confirm it is sending the right signals at the right times.
  • We inspect the cylinder for leaks, corrosion, scale and missing or damaged insulation.
  • We replace failed controls and valves once you have agreed the price.
  • We give honest advice on whether an older cylinder is worth repairing or would be better replaced.

What to plan before you book

Know which type you have

Open the airing cupboard and have a look. A bare or foam-covered copper cylinder with a cold water tank in the loft is usually vented. A white or coloured cylinder with a cluster of valves, a pressure gauge and a small round expansion vessel nearby is usually unvented. A photo of the label helps.

Note the symptoms

Write down exactly what is happening. Is there no hot water at all, not enough, or water that is too hot? Does the central heating still work as normal? Did the problem start suddenly or build up over weeks? These small details help narrow down the fault before we arrive.

Clear the airing cupboard

Most airing cupboards double as linen stores. Take out towels, bedding and anything stacked around the cylinder so there is room to reach the thermostat, the valve and the pipework. It saves time on the day and means nothing gets damp if a joint has to be opened.

Think about how you use hot water

If replacement is on the cards, think about how many people use hot water at once, how many bathrooms you have, and whether baths or showers are the norm. Cylinder size and type depend on that, as well as on your incoming mains water pressure and the space available in the cupboard.

Good to know

Unvented cylinders need the right installer

Building regulations require unvented hot water systems to be installed by someone holding the G3 unvented hot water qualification, and they should be serviced every year in line with the manufacturer's terms so the safety devices keep working. If you are not sure who fitted yours or when it was last looked at, it is worth finding out.

Keep stored water hot enough

Stored hot water should reach at least 60°C so that bacteria such as legionella cannot settle in. If you have young children or older relatives at home, mixing valves on the taps can bring the outlet temperature down while the cylinder stays at a safe setting.

Insulation makes a real difference

Older copper cylinders with a loose fabric jacket lose a surprising amount of heat into the airing cupboard. Modern cylinders have factory foam insulation, and better insulation means the water stays hot for longer between heating cycles and the boiler fires less often to top it up.

The immersion heater is a useful backup

If your cylinder has a working immersion heater, it can keep the household going while a boiler-side fault is being fixed. It costs more to run than gas, so it is best used as a short stopgap rather than left switched on all the time.

How it works

  1. 1

    Describe the problem

    Tell us what your hot water is doing and which type of cylinder you have, using the enquiry form. Any make or model details from the cylinder label help.

  2. 2

    Arrange the visit

    We agree a time that suits you and let you know what to have ready before the visit.

  3. 3

    Find the fault

    We test the programmer, thermostat, valve and boiler side of the circuit in turn until the cause is clear, then explain what we have found in plain terms.

  4. 4

    Repair and test

    We price the fix, carry it out once you agree, and run the system to check the cylinder heats properly and switches off as it should.

Hot water cylinders in Hackney, Islington and Shoreditch

Many Victorian terraces in Hackney still run a regular boiler, a loft tank and a copper cylinder on the landing, often fitted decades ago and patched since. Those systems are well worth keeping going when the cylinder is sound, and a new valve or thermostat is often all they need. In Islington, Georgian and Victorian houses split into flats can have cylinders squeezed into tight cupboards, with pipework shared or rerouted over the years.

Shoreditch has more warehouse conversions and newer flats, where unvented cylinders are common because they give good pressure without a loft tank. Those cylinders need their safety valves and expansion vessel looked after. Wherever you are in the three areas, we check what is actually installed rather than assuming, and give advice that fits the building.

Questions customers ask

Why do I have heating but no hot water?

Usually the motorised valve has stuck, the cylinder thermostat has failed, or the programmer is not calling for hot water. Each of these can be tested in turn, and it is rarely the cylinder itself. We find which one it is before replacing anything.

Can I use the immersion heater in the meantime?

Yes, if your cylinder has one and it works. It will heat the water while the boiler side is being repaired. Switch it off if you see any water leaking near the immersion or its wiring.

Should I repair or replace my cylinder?

If the cylinder is sound and the fault is in a control or valve, a repair is usually the sensible choice. A cylinder that is leaking, badly corroded or very poorly insulated may be better replaced. We explain the options and leave the decision with you.

What is the difference between vented and unvented?

A vented cylinder is fed from a cold water tank in the loft and runs at low pressure. An unvented cylinder takes water straight from the mains, giving stronger flow at the taps, and has extra safety valves and an expansion vessel to manage that pressure.

Why is water dripping from a pipe outside my house?

On an unvented system that pipe is usually the discharge pipe from the safety valves. Water coming out means a valve is releasing pressure or heat. It should be looked at soon rather than left to carry on.

Why does my hot water run out so soon?

Common causes are a thermostat set too low, scale on the heating coil, a programmer giving too little heating time, or a cylinder that is simply too small for the household. We check the controls first, as they are the easiest to put right.

No hot water?

Tell us what your cylinder is doing and we will arrange a visit to find out why.